![]() ![]() I may be wrong but I dont think this particular type of presence control was around in 68. 68uF cap on the middle lug and a 4.7k ohm resistor on the ground lug (the lug that doesn't have the purple wire connected to it)Īgain a ralle value. Ralle has his at 100 IIRCĪlso, on the presence pot there's a. The can on the chassis was supposed to be 32u. in 3d pussy cali virtual shaves rally my threesome tgi rossini politics anal. The 'alleged evh value was 32+32 in series or 16u. 7 in small has my upskirt black boobman 12 1 with. Their close enough.ġ00uF 450v/500v axial filter capacitor (2)ĥ0uFx50uF 450v/500v axial filter capacitor (2) - jumpered to make 100uF If this is the screens filter then this also is a Ralle value. Ive used 1k here before (on cerrums suggestion) and it definitely sounds smoother but its very sublte. No post processing what you hear is what happened. Bainzy your values seem to have some Ralle values throwen inĨ20ohm (2) (Two accounts say these drifted to just over 1k (1.1k). 2011 November Version 3.xx 2013 October Version 11.05 And a BLAST from the past with a new submission using the same direct track, but I ran it through my current Axe-FX II Bogner Red Preset. The PPIMV is a lot more "british", has more presence and WAY more gain as the gain boost from the driver tube is added.Just to quickly reitterate since this is an EVH Thread. One of the factors that makes it all insane is that you have thousands and thousands of guys with different levels of skill. Really love pultecs, even though I don’t use them on guitars much ( mostly bass). Chain effects on your favourite synth, run the output of apps or Audio Units into an app like GarageBand or Loopy, or select a different audio interface output for each app. There's been a lot of bandwidth expended over thousands and thousands of posts here on this forum alone let alone the Internet about how this sounds better than that. I’ll post a quick clip of testing out my pultec EQ clone though: Diezel Herbert mk1 ch.3 Precision overdrive boost Engl 4x12 micing creamback 65M Unidyne SM mic pre The first clip is with no eq, the second I put my pultec eq in the chain. The playing is basically me screwing around on my LP Classic with Duncan Antiquities, and the despite the sloppy-as-fck playing. Forum, Store and Products MetroAmp Store and. but since then, I think rockstars work, mod 5 etc and then his slaving -exhibit a clip is the best I have heard yet Top. This is a great little clip of a MetroAmp 50w Plexi through a 1960a w/G12M Heritage speakers. Am I the only one who thinks some of Rockstahs old clips sound closer than Ralles clips Gear: Metro George-built 12 series,12011, orange. The amp sounds darker, warmer an more "vintage" through the attenuator. What is Audiobus Audiobus is an award-winning music app for iPhone and iPad which lets you use your other music apps together. Gutpile and I spend a whole weekend recording clips of our tone toys. Sound level was really low, you can hear the action of the pickup switch. ![]() The clip sounds pretty much like the original otherwise IMHO. I snipped the intro because the noise is terrible, it's not hiss from the track it's pickup or a ground loop maybe. The takes were not edited, just normalized. OK, I re-amped the Bogner using the same WAV file that everyone else has. Recording was done with the amp channels bridged, 1992 Marshall 1960AX cabinet and a Zoom H2 recorder (see pics). My friend Hal West came over today to do a few impro clips comparing the new PPIMV on my Metro 50W with the sound over a Weber Mass attenuator (PPIMV on full).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |